BT-7200APP Clamp Multimeter

UPC:783903696715

Title: BTMETER BT-7200APP TRMS 6000 Counts Clamp Multimeter, Digital Clamp-on Ammeter for AC/DC Current Voltage Resistance Capacitor Frequency Continuity Temperature NCV

• ⚡【Remotely Monitoring on Your Phone】 Built-in wireless connectivity can auto connect to your Android / Apple phones or tablet with ease, allows you viewing logging the data out of the arc flash zone 15m (50 ft) away, and save the measurement for detailed analysis, sharing later.
• ⚡【AC DC Clamp Amp Voltmeter w/ NCV】This clamp multitester can accurately measure AC/DC Amperage, AC/DC Voltage, Resistance, Frequency or Duty Cycle, Capacitance and also provides Noncontact AC Voltage(NCV) detection, Diode, Continuity Buzzer and Temperature(℃/℉) tests. Easy to use in non-contact ampere measures, troubleshoot electrical problems in , motors, household appliances, HVAC
• ⚡【Continuous Data Logging Clamp DMM】This clamp-on meter can displays AC DC amps, volts, ohms, Cap, Hz Temp in Max/Min/Avg on the same interface with real-time reading. The curve graph w/ timing will show you the changes of amp volt flow more visually. Also supports adjustable data logging rates for continuous testing/ recording unless the battery is dead or the memory is full.
• ⚡【Reliable True RMS Voltage Amperage Meter】0.1 amp resolution for 0.1 ~ 60A AC DC current, 1A for 60 ~ 400A to support accurate amp reading, this clamp amp probe meter is more user-friendly for daily current measurement, such as troubleshooting car, boats battery
• ⚡【Clamp On Live Wire for Measurement】To measure amp with this clamp meter, you MUST separate the hot and neutral conductors, and clamp around only LIVE wire for measurement otherwise they will cancel each other out and give a zero amp reading. The most convenient way without peeling the cord is clamp on an AC Line Splitter

  ---

  BTMETER BT-7200APP Intelligent Autoranging Digital Clamp Multimeter

  Wireless Control & Logging on Mobile Phone Tablet

• Phone/Tablet APP "AILINK" available on App Store, Google Play.
• Average sensing, calibrated to rms of sine wave on AC Volt, AC Amperage test.
• This AC/DC clamp-on ammeter is ideal for remotely troubleshoot electrical problems
• Sync electric data to your phone via Bluetooth APP, display all measurement and generates analog waveform graph on APP
• Large display + Front Light helps you measure with ease at dim area
•  
• Specifications:
• DC Current: 60A/400A ±(2.5% / 3.0% +10 digits)
• AC Current: 60A/400A ±(2.5% / 3.0% +10 digits)
• AC Voltage:6V/60V/600V ±(1.0% ~ 1.5% +3 digits)
• DC Voltage: 600mV/6V/60V/600V( +/- 0.5% ~ 0.8% + 2 digits)
• Resistance: 600Ω/6KΩ/60KΩ/600KΩ/6MΩ/60MΩ
• Capacitance: 9.999nF/ 99.99nF/999.9nF/9.999µF/99.99µF/999.9µF/9.999mF/99.99mF
• Frequency: 9.999Hz/99.99Hz/999.9Hz/9.999kHz/99.99kHz/999.9kHz/9.999MHz
• Duty cycle:0.1%~99.9% ; Temperature Test: -4 ~ 1832 ℉

  What’s in the pacakge?

• 1 x User Manual
• 2 x AAA Battery
• 2 x Test Leads (Pair)
• 1 x Small Screwdriver
• 1 x Temp Probe
• 1x BT-7200APP Clamp Ampere Meter

More Features:

• Data Hold
• Diode Test
• MAX/MIN/AVG
• Front LED Lamp
• Backlight Display
• Overload Protection
• Temperature Test (℃/℉)

Wireless Connect with your Phones

Automatically pair with one bluetooth device in just few seconds.(Shut down other unnecessary bluetooth signals during pairing.) The App can be used in IOS 7 or android 4.30 and up. Support Bluetooth 4.0 version.

Both AC/DC Volt Amps Clamp Meter

It can accurately measure DCV to 0.1m volt, ACV to 1m volt; DC/AC Current to 0.1 amp; Resistance to 0.1 ohm. Features with “REL” to zeroing for magnetic environment to make sure you get accurate readings anytime,anywhere.

Remotely Monitor Logging

The app will synchronous display the readings, also with MAX/MIN/AVG and measuring time, it means you can remotely record the readings every 1-120 mins from different floor, ground to roof, within 49ft.

BTMETER BT-7200APP Connect Instructions

1. Scan the QR code or Search “AILINK” on Google Play/ APP Store.

2. Turn OFF ALL irrelevant bluetooth signal. → Turn on the Bluetooth on your mobile phone.

3. Open the APP → Turn on BT-7200APP Wireless Multimeter → Wait for it shows up on your APP→ Select to Connect

4. Press “Start" button → Enjoy your measurement.

5. Share the electric datas with your co-worker via FB